Cars hate me

[JamezF]

I have an Octavia, 54 plate, 259,000 miles. Used mainly as a bee car now. I had a similar problem years ago with a rear door. It was sorted by local garage without removing the rear door panel. I'm not sure how, but a lot of the central locking control is in the drivers door. Corrosion is a problem with the multipin connector in that area. Only problem with EGR was a leaky air pipe, easily fixed.
https://www.briskoda.net/ is a good forum for Skoda. Good luck.

54 plate would be a Mark 3 I think? Ours is a Mark 2. Impressed that it has done such a high milage though. There are some models that seem particularly prone to problems as far as I can tell. Ours has been particularly bad since Skoda did a recall to reprogramme the ECU in the light of the events of the VW emissions scandal. It's also a problem that we don't really do very many long journeys any more. Our local mechanic showed me a photo of the throttle body before he cleaned it a few months back. It was probably reduced to about a third of its diameter by being caked in soot that re-enters the airflow via the EGR valve.

I'm told that welding the door closed, "Dukes of Hazzard" stylee would not be a problem MOT wise, so that's my last resort Not sure how my wife will feel about sliding across the bonnet and climbing in through the window though.

I've tried all the tricks that have been suggested with revving the engine whilst unlocking the doors, bumpy roads etc. etc. My gut feeling is that a linkage has come loose or broken, so I need to get inside to find out. The door card looks like it has four retaining screws, two under the handle to pull the door closed and two at the bottom where they may be obstructed by the sill. If I can get them out then it allegedly just lifts up and off. If I can't get to the screws then I'll probably just introduce the door card to my Dremel, and perhaps I'll replace it afterwards if it bothers me that much.

James

 

[JamezF]

Ho ho. Having spent much of the day upside down with my head in the passenger footwell and my feet dangling out through the driver's door in the rain, I finally managed to remove the five screws retaining the door card. Four were actually quite easy. The last was an absolute pig. At one point I was actually contemplating removing the front passenger seat altogether just to make it easier to get at. So I finally lifted the door card away to reveal...

It seems that Mr Skoda doesn't want me to get at the lock mechanism that easily Having watched a fair few ewechoob videos it would appear that if you splash the cash and buy a VW, this steel door liner is screwed to the inside of the door. If you're a cheap git (ie. me) and buy a Skoda, you get pop rivets instead. There are nine that I now have to drill out, having first ensured that the electric window doesn't fall out when I remove the liner. That can be tomorrow's problem.

Sliding a double length of packing strap down the window no longer appears to be an option as these days locks often have a cover to prevent such interference. And in fact they're so complicated that finding the right bit to move would be a nightmare. It's entirely possible that a single modern door lock has more moving parts than my entire first car.

(Honestly, I really did look at how much it would cost to get a replacement door from a scrap dealer so I could just take an angle grinder to the current one to get it to open.)

James

 

[Penninetrader]

Ho ho. Having spent much of the day upside down with my head in the passenger footwell and my feet dangling out through the driver's door in the rain, I finally managed to remove the five screws retaining the door card. Four were actually quite easy. The last was an absolute pig. At one point I was actually contemplating removing the front passenger seat altogether just to make it easier to get at. So I finally lifted the door card away to reveal...

It seems that Mr Skoda doesn't want me to get at the lock mechanism that easily Having watched a fair few ewechoob videos it would appear that if you splash the cash and buy a VW, this steel door liner is screwed to the inside of the door. If you're a cheap git (ie. me) and buy a Skoda, you get pop rivets instead. There are nine that I now have to drill out, having first ensured that the electric window doesn't fall out when I remove the liner. That can be tomorrow's problem.

Sliding a double length of packing strap down the window no longer appears to be an option as these days locks often have a cover to prevent such interference. And in fact they're so complicated that finding the right bit to move would be a nightmare. It's entirely possible that a single modern door lock has more moving parts than my entire first car.

(Honestly, I really did look at how much it would cost to get a replacement door from a scrap dealer so I could just take an angle grinder to the current one to get it to open.)

James

I think you are taking the right approach.I have had 2 cars with this problem, one a zafira and the other a Saab sport wagon. I have no experience of Skoda but if there is any orifice through which you can fire thin oil that will land around the lock mechanism it might help with your problem. The throw of the lock mechanism needs very little resistance to stop it's functioning. I am presuming that you can tell the lock mechanism is active via sound when pressing the transponder. This was my Saab fix. The entire mechanism on it was security shielded.

 

[Garry R]

Had same sort of problems when I had an Octavia Estate found the final problem to be the black box that connects to the ECU it is positioned under the vent at the back of the bonnet and can fill with water.Changed black box and ECU and reprogrammed myself.Saved myself a few pounds.

The Rover 75 obviously had an inspirational designer who thought it was a great idea to put the ECU in the well underneath the windscreen. This was all great if the drainholes in there were kept clear which in many cases was not done and the ECU would flood leading to complete failure.

 

[pargyle]

The Rover 75 obviously had an inspirational designer who thought it was a great idea to put the ECU in the well underneath the windscreen. This was all great if the drainholes in there were kept clear which in many cases was not done and the ECU would flood leading to complete failure.

Yes ... I've had 3 Rover 75's and the first thing you do when you get one is make sure the plenum drains are clear and then spend £8 on a bit of plastic grill that goes over the top where the leaves collect that stops them blocking the plenum drain ! An aftermarket mod invented by a Rover 75 enthusiast and sold to those who know about the problem. Fortunately I avoided the dreaded drowned ECU which in many cases led to the cars being scrapped.

Other than that it was probably the best designed and built Rover ever made - BMW 3.0 series underneath and the 2.0l diesel engine was bomb proof. We had few problems ever with any of ours - the occasional air bag warning light coming on as a result of a stupidly positioned connection under the front seats where every time you moved the seats the connector came loose ! I never did fix it ..

The only reason we no longer have one - the estate tailgate was so heavy 'er indoors could not lift it, even with new enhanced gas struts. Replace them - "Any car you like" she said as long "As it has an electric tailgate ..."